|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-03-2014, 12:04 PM
|
#1 | ||
|
When in doubt, GAS IT!!
Join Date: Sep 2006
Location: Lower Eyre Peninsula, SA
Posts: 3,018
|
The car is in pieces as we speak so I need an answer asap if anyone can help. I need to replace the drivers side tie rod as the rose joint is rattly and loose plus I'm changing the wheel bearing/hub at the same timel but the tie rod doesn't seem to want to budge and undo from the rack. I can feel that there is a small cut out on the bottom of the rack shaft where the tie rod screws in and was wondering if it's a key way or something as I can't get my fat head under there with the car just jacked up and supported. Is there a key way under there with a key locking the tie rod in place or is it just that the tie rod is stupidly tight and I just need more leverage? I don't want to go leaning on it if it is locked in place as any number of nasty things can potentially happen if I put enough muscle into it, so any guidance would be much appreciated.
Cheers Bushbasher
__________________
. HERS- BFIII Wagon Gold, alloys, dual fuel, bullbar, big tow pack, trans cooler, fully rebuilt HD suspension, Clarion, alarmed, full 2 1/2" sports system, mint body MINE- AUII Forte Meteorite, dual fuel but otherwise bog stock. MINE- AUII Fairlane Sportsman Liquid Silver over meteorite,HIDs', Airhog, Eagle Leads, dual fuel, custom rear springs, BA slotted discs + a second one for spares . |
||
|
|
|
06-03-2014, 03:14 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
Its been a few years since Ive been under an AU but its not a Left handed thread by any chance?
It will be a lock up nut and rod end shouldnt be a key/way there. More leverage abit of WD40 in the right direction mate.
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
|
|
|
|
06-03-2014, 04:23 PM
|
#3 | ||
|
When in doubt, GAS IT!!
Join Date: Sep 2006
Location: Lower Eyre Peninsula, SA
Posts: 3,018
|
No left hand thread, it was just a bloooody tight fit. Turns out that the cut out I thought might be a key way was just a gap cut into end of the shaft to allow some penetrene or the like to be squirted onto the threads, at least that's my best guess, either that or it allows the shaft to spread fractionally when you screw the tapered thread of the tie rod in to it, to keep it tight.
All fixed and good to go. Cheers Bushbasher
__________________
. HERS- BFIII Wagon Gold, alloys, dual fuel, bullbar, big tow pack, trans cooler, fully rebuilt HD suspension, Clarion, alarmed, full 2 1/2" sports system, mint body MINE- AUII Forte Meteorite, dual fuel but otherwise bog stock. MINE- AUII Fairlane Sportsman Liquid Silver over meteorite,HIDs', Airhog, Eagle Leads, dual fuel, custom rear springs, BA slotted discs + a second one for spares . |
||
|
|
|
| This user likes this post: |
HELP URGENT!! Need help to get the tie rod off.
Linear Mode
