|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
| OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS |
 |
|
|
Thread Tools | Display Modes |
28-01-2007, 01:27 PM
|
#31 | ||
|
V8 Turbo Hoon
Join Date: Jan 2005
Location: Melbourne
Posts: 1,634
|
you wouldnt happen to take any photos of the fmx shifter setup?
|
||
|
|
|
28-01-2007, 01:47 PM
|
#32 | ||
|
around the place
Join Date: Jan 2005
Location: Perth
Posts: 1,754
|
unfortunatley i didnt take any photo's when i did it, it was a real ***** of a job too, because the extractors barely give you enough room to get your fingers up the side of the box.
The trans linkage used is the c4 one that comes with the shifter, but its been bent outwards a bit, and cut the lever off it extend it slightly and weld it back on. The cable bracket i made bolts onto two of the rear pan bolts on the FMX and has another plate coming off at around 90 degrees on the left hand side where the cable goes through.
__________________
GPS Tracker for your vehicle - PM me for info |
||
|
|
|
| This user likes this post: |
|
13-04-2014, 12:43 PM
|
#33 | ||
|
Starter Motor
Join Date: Apr 2014
Posts: 3
|
I'm looking for someone who has gone down this track and fitted a B&M shifter to their EB2. I currently own a very tidy EB2 XR8 and have been thinking about upgrading the shifter to a B&M. Is there anyone out there with some good pics and advise?
|
||
|
|
|
| This user likes this post: |
|
13-04-2014, 11:09 PM
|
#34 | ||
|
GTP-RPD
Join Date: Mar 2005
Location: Adelaide
Posts: 359
|
Let us know how you go. All avenues I have checked out have come up a no go. It's our gearboxes that are an issue. Not compatible with the shifter kits.
|
||
|
|
|
14-04-2014, 09:59 AM
|
#35 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2005
Posts: 2,881
|
i know dtm transmissions in geelong have fitted b&m shifters into ba 4 speeds give them a call (03) 5222 1833
|
||
|
|
|
|
18-04-2014, 01:03 PM
|
#36 | ||
|
Starter Motor
Join Date: Apr 2014
Posts: 3
|
Thanks for your input guys. As far as I have learned so far B&M make an additional kit for fords with an AOD four speed transmission $148NZD. I think, yet I have to confirm that is what we call the BTR here down under. Because the 5L MPEFI V8 is American, I can only assume so is the transmission thus it must be the 4 speed Automatic Over Drive they call AOD. I'll keep you posted on my research.
|
||
|
|
|
|
19-04-2014, 06:15 PM
|
#37 | ||
|
around the place
Join Date: Jan 2005
Location: Perth
Posts: 1,754
|
hey mate the BTR is an aussie 4sp different to AOD/E
you would need to make your own cable bracket to suit the BTR auto there wont be anything off the shelf
__________________
GPS Tracker for your vehicle - PM me for info |
||
|
|
|
Linear Mode
